Shear, 1.5 mm Grid Length, 1.5 mm Grid Width
Click and hold to zoom
Data Sheet (PDF)
$288.65
Item#1-XM41-1.5/350GE
Volume discounts available
Volume Discount Schedule
Quantity | Price each |
---|---|
1-4 | $288.65 |
5-9 | $274.22 |
10-24 | $268.44 |
25-49 | $256.90 |
50-99 | $251.13 |
100+ | $245.35 |
Added to Your Shopping Cart
Configuration complete.
Please add to cart to keep it or exit the configuration
Failed to Save Configurations, Click on Configure Button Start Again
In stock
Lead Time (If not in stock): 14 weeks
- High Resistance to Alternating Loads
- High Temperature Range 300°C (572°F)
- Wide Spectrum of Different Types
- All models sold in a 5-pack, except 1-LM11 which are sold in a 10-pack
View Specs
1-XM41-1.5/350GEModel Options
View all models
Edit these specs to order a different model. Not all combinations are valid. Options compatible with previous selections will be in bold.
*Highlighted options are not compatible. Please select a different combination.
Grid Length Range
Grid Length
Grid Width
Grid Style
Temperature Range Units
Temperature Range Min
Temperature Range Max
Connection Type
Resistance
Maximum Strain
Features
Edit Model Options
Shear/Torque Strain Gages are for measuring shear strain and torque, typical applications are for measurements on torsion bars and determining shear stresses in shear beam load cells. M Series strain gauges have been specially developed for high resistance to alternating loads at increased strain levels and high temperatures up to 300°C (572°F). They are foil strain gauges with measuring grids made of a special nickel-chromium alloy. OMEGA/HBM offer this special strain gauge with various geometries, measuring grid lengths and temperature response matching. New materials offering high strength such as fiber composites pose a major challenge for strain gauges used for measurements specifically when pushing components to their mechanical limit of performance. Situations may arise where a strain gauge subjected to alternating loads at increased load levels is weakened and fails earlier than the component under test. The M Series has been specially developed for high resistance to alternating loads and allows for testing of materials featuring high strength. All M Series strain gauge types are available with different measuring grid lengths: The right measuring grid length: The measuring grid length depends on the aim of measurement, since the result of a measurement with strain gauges will be determined as the average of strains. In general, measuring grid lengths of 3 to 6 mm (0.06 to 0.24') generates a better result. Long measuring grids are recommended where there is an inhom*ogeneous material such as concrete or wood. A long strain gauge will bridge the inhom*ogeneity of the work piece and return the strain underneath the measuring grid as the measurement result. Short measuring grids are suitable for detecting a local strain state. Therefore, they are suitable for determining strain gradients, the maximum point of notch stresses and similar stresses. Specifications
• 1.5 mm: where space is a constraint or when highly selective measurement results are required
• 3 mm: for inhom*ogeneous materials and where space is a requirement or not
• 6 mm: for inhom*ogeneous materials and where space is not a requirement
Strain Gage Construction–Foil Strain Gauge
Carrier:
Material: Glass fiber reinforced phenolic
Thickness: 35 ±10 µm
Grid Foil:
Material: CrNi
Thickness: 5 µm
Encapsulation:
Material: Polyimide film
Thickness: 25 ±5 µm
Connections: Solder pads with strain relief
Resistance: 350 and 1000 Ω
Resistance Tolerance: ±0.3%(1)
Gage Factor: Approximate 2.2 (specified on each package)
Gage Factor Tolerance: ±1.5% (for grid length <3 mm) ±0.7% (for grid length ≥3 mm)
Temperature Coefficient of the Gauge Factor: Specified on each package
Transverse Sensitivity: Specified on each package
Operating Temperature Range: -200 to 300°C (-328 to 662°F)
Temperature Response (Ferrite Steel): 10.8 ppm/K (6.0 ppm/°F)
Maximum Elongation:
Positive Direction: 10,000 µm (1%)
Negative Direction: 15,000 µm (-1.5%)
Minimum Bending Radius: 5 mm (0.20') for linear gauges 10 mm (0.39') for stacked rosettes
Bonding Material that Can Be Used: Z70 or EP310S
Fatigue Life (Test to Failure):
107 cycles at 2000 µm/m
106 cycles at 2200 µm/m
104 cycles at 3100 µm/m
Data Sheet (1)
HBM-M-Shear_spec
Compliance Certificates (1)
- RoHS 2015/863 - View Certificate
Related Products
Pre-Wired Strain Gauges for Easy Installation
Pre-Wired Gages Make Installations Easy!No Soldering at the Measuring PointSold in Packs of TenEach Gage has 50 mm of PTFE Cable before Transitioning to AWG 28 Leads to Prevent Leads from Adhering During Installation.
See More
Biaxial, 0/90° Corner T Rosette Strain Gauges
Conveniently Priced per Pack of 5General Purpose Strain GagesVery Flexible, Mechanically StrongSmall Bending Radius.
See More
Dual Parallel Grid, Linear Strain Gauges
Precision Parallel Grid Gages for Bending StrainConveniently Priced per Pack of 5Very Flexible, Mechanically StrongSmall Bending Radius.
See More
3 Element Stress Relief Strain Gauges
Very Flexible, Mechanically StrongSmall Bending RadiusBroad Temperature RangeAffix with Cold or Hot Curing Adhesives.
See More
Karma Shear And Torque Pattern Gauges
Sold in Packages of 5 gages K-Series, Premium Karma Strain Gages Available as Single ¼ Bridge, Single Matched Reversed Patterns, ½ Bridge with Separate Connection Pads, or ½ Bridge with Common Connection Tab Custom Gages Available - Fast Delivery.
See More
More Related Items
karma shear and torque pattern gaugesstrain gages pack of 100karma strain gaugepre wired strain gauges
Related Categories
torsion shear strain gaugeslinear strain gaugesdual parallel strain gaugesstrain gauge accessoriesrosette strain gauges